CeraTrim - Ceramic Powered Trim Restorer (8 oz.)
*** Please Note: Due to very high demand of CeraTrim and bottle shortages caused by COVID, some CeraTrim orders may come in clear bottles instead of black. It is the exact same product though.***
Brought to you by The Last Coat comes our ultra-durable ceramic-based trim restorer, CeraTrim.
CeraTrim uses our popular and effective ceramic technology to bond deep into the pores of plastic trim surfaces, removing the impurities that have built up in the plastic and effectively restoring them to their original appearance. Check out the video below to learn more and to see how easy it is to apply and how much to use:
Unlike most trim products, CeraTrim is no mere dressing or stain. It is a true ceramic coating that will give your trim surfaces superior hydrophobic and self-cleaning properties and will protect your trim for the long haul under any driving conditions while restoring them to a newer appearance.
CeraTrim can be used on all trim pieces throughout your vehicle, inside and out. It can be used on engine bay plastics to restore their appearance.
We have also used CeraTrim as a durable tire dressing, but keep in mind this is an "off-label" use and requires 2-3 coats. (please note for interior pieces it will make them glossy, so if you prefer the matte look, best to avoid CeraTrim for the interior.)
CeraTrim can be layered to get an even higher shine or deeper wet look, and even more protection. It can be re-applied over time as desired as well.
All CeraTrim Kits Come with the Following:
➡️ 1 x 8 oz. Bottle of CeraTrim
➡️ 1 x Foam Applicator (this is our preferred way of applying as seen in our videos. We like the foam applicator provided as it allows us to push CeraTrim into the pores of the surface more effectively.)
Directions for Applying CeraTrim:
Step 1: Plastics and rubbers need to be as clean as possible before applying CeraTrim. Any prior dressings should be removed. You do not want anything affecting the bonding of CeraTrim to the trim surface. You will want to use a basic vehicle soap (no wax-based soaps), but in addition, you will need to use a degreaser or all-purpose cleaner (APC) and a soft bristle brush to agitate down into the texture of the plastic or rubber.
Step 2: With high-pressure water, thoroughly rinse the area ensuring to get full removal of any soaps or detergents.
Step 3: If the plastic or rubber doesn't become fully clean and bare, repeat the process until you achieve the deepest clean possible.
Step 4: Thoroughly dry the plastic or rubber and then apply CeraTrim with the included applicator.
Step 5: Allow it to dwell for 5-20 minutes (depending on how faded the surface is).
Step 6: IMPORTANT - DO NOT SKIP THIS STEP - After the dwell period take a dry microfiber towel and buff the trim surface to remove excess residue that will be sitting on top. This is very important.
Please Note: Full cure time for CeraTrim is 24 hours. Do not let these surfaces get wet in the first 24 hours after application.
We know you'll love CeraTrim as much as we do and as much as our customers have. It is a versatile, durable, true restoration product that will bring trim plastics and rubbers back to life in a big way, and keeping them looking that way for a long time! If you have any questions, feel free to reach out to us.
***Please note, applying CeraTrim can make surfaces very slick when wet, so when applying to running boards on your vehicle please keep this in mind as they may be quite slippery when wet.***
It was very easy as the dirt just seemed to melt off when I washed the car. Applying the wax was amazing as the car just looked great.
I have used The Last Coat, Amp and Cerama Trim on multiple vehicles. Unbeatable shine that lasts several months, through several washings.
Purchased replacement wheels for my daughters Mustang. Thoroughly cleaned front and back with TLC. Double coated front and back of the wheels before installing them. Super pleased with the satiny smooth feel and shine. Can’t wait to do both Mustangs with TLC. Happy, satisfied customer
I just buffed a 47’ yacht, applied 2 coats of TLC and a topper of AMP. Product are easy to work with (vs carnuba wax and a buffer!). Boat shines beautifully. Cleans up the easiest I’ve ever experienced. Used pH neutral soap minimally. Wipes up nicely with absorbent towels. Now the true test, how well does it hold up over time in a marina. Plan to AMP periodically. Any other tips?
Hi Matthew, On marine purposes we do recommend 2-3 layers with 24 hours cure time between each. Best Regards, Brian Team TLC.